With this adaptor you can run a mavic air battery for more flight time.
Magic spark adaptor with the added mavic air connector and xt30 swap out your spark battery for a mavic air battery you will still receive the battery telemetry.
No need for soldering of the MA battery just plug in and fly there will be the added weight of this connector which is 2 grams but it means you can fly with MA battery as it is or remove the outer casing to reduce weight.
For better results it is best to remove outer casing which is not hard only 6 clips around the battery casing.

Have you crashed your DJI Spark this repair is for replacement of the frame only.

For hardcore flyer comes a hardwired solution for the expert flyers looking to save on weight and get that bit more of of your spark on them long range runs.
We will fit your spark with a JST cable soldered to mainboard.

You get 1 battery holder and 1 mavic pro power adaptor

Batteries not included

Have you a Broken the Micro USB charge port on Mavic Air Remote Control unit the micro USB is easy broken on the new Mavic Air remote by putting the cable in the wrong way round.
We will replace it with a new micro A/B port

Have you a Broken the Micro USB charge port on Mavic 2 zoom Remote Control unit the micro USB is easy broken on the new Mavic 2 remote by put the cable in the wrong way round.
We will replace the micro USB on the PCB board.

2 XT60 Adaptor for running 2 batteries on each side of the Mavic 2 pro/zoom.
Get up to 38mis filght time.
Before buying if you need more info on battery mods this can be found on facebook groups please check these out if you do not know or never run mods before.
Here is a group that will help you out in running battery mods on the mavic 2, Long Range 4 Life
and the link to it is,
https://www.facebook.com/groups/371300420338551/

One of the best ways to holder your external batteries to your DJI Mavic 2 is this special made holder.
Battery opening is 1.42 inch.
It comes in black only!

This repair service is for replacement of the micro USB port on the spark.
We will replace the micro USB port on the PCB board.

More flight time for your Mavic 2 pro
Now Ver.2 with 3 XT60 connectors to run a single or 2 batteries on each side of the Mavic.
Get over 40 mins plus with the right battery setup.

Has one of your buttons on your DJI Maivc Pro remote not working or stuck or you have damaged the micro USB port? This service is for USB, 5D joystick button,record button,shutter button repair for you DJI Maivc Pro Remote Controller.
The micro USB is easy broken by put the cable in the wrong way round.

You Must run this mod in Non-dji battery mode. Which can be changed from the DJI Assistant 2. Ver 1.1.2.
Also you will need to disconnect the bottom sensor cable from the spark if you want to use a bigger battery.

Batteries best used 1300mah to 1850mah maxamps
25 mins plus flight time.
Picture below on how it is fitted.

The best way to mount two external batteries to the Mavic Pro
Easily clip on and off
Comes with velcro straps

DJI Mavic Air Battery Power mod Adaptor High quality Adaptor for increasing flight time
LED light so you know when to connect the aux battery
Its best to use a single 1400mah lipo 11.1v this will give you 22 mins plus or a 3000 mah 30c 3s
To get the most out of this mod you will have to run it in non-dji battery mode
Has been tested up to 30mins flying time with a 3000 mah
More flight time for your Air.
More info on this mod can be found on the facebook group here link below,
https://www.facebook.com/groups/DJIModsMavicAir/

XT60 Parallel cables for running 2 batteries from the power adaptor on the P3
Also can be used with the Phantom 4.

We ship worldwide.

Get longer flight times for longer range flying and time-lapse videos.
There is no need to open battery to fit this device.
You can fit two 2200mah zippy compact 4S batteries which will give you total 30 mins flight time. (Batteries not supplied).
High demand Please allow 5 days before shipping

Obtain a wider range and increased flight time with this battery adaptor fitted with a XT60 connection.
Take a look at the range you could be getting picture to the right.
You have no need to modify the Mavic at all.
And your warranty will stay intact
Requires 1 or 2 aux batteries (not supplied). You can use two 1600mah/3000mah 3S LIHV batteries. Purchased separately from Hobbyking.
Includes a LED light so you know when to connect the aux batteries.

Parallel cable for running 2 lipo batteries these are made up to right size to
run down to the battery holder.
Color of cables may vary
We ship worldwide.
batteries not included.

The kit comes with 1 Power adaptor clip a set of Y cables and battery mount.
You will need to supply your own external batteries
We ship worldwide.